工藝:焊接頭切割的參數設置(中英)

超強偉業焊接頭的切割設置

Cutting setup for super weld head


一.銅嘴

使用切割銅嘴(建議銅嘴1.5以上)

One. Copper tip

Use cutting copper tip (recommended copper tip 1.5 or more)




二.工藝

Ii. Process


與焊接不同的是,切割光斑是沒有寬度的,因此掃描寬度務必設置為0,即紅光為一個點

其他參數(峰值功率:參考值)(占空比:參考值100%)(脈沖頻率:參考1000%)同焊接一致

設置參數后,導入并返回,即可在首頁的左側看到此工藝

焦點建議使用負焦(直接影響切割效果)


三:信號的檢測

只有【激光器扳機信號】和【安全地鎖信號】有效時,才會出光(激光器狀態正常),同時首頁未出現任何報警

關于首頁的報警,多數是(設置)里面的報警電平設置錯誤,請更改對應的報警電平


Unlike welding, the cutting spot has no width, so the scanning width must be set to 0, that is, the red light is a point

Other parameters (peak power: reference value) (Duty cycle: reference value 100%) (pulse frequency: reference 1000%) are the same as those for welding

After setting the parameters, import and return, you can see the process on the left side of the home page

Negative focus is recommended (directly affecting the cutting effect)



Three: signal detection

Only when [laser trigger signal] and [safety lock signal] are effective, light will come out (laser state is normal), and there is no alarm on the home page

About the alarm on the home page, most of the alarm levels in the (setting) are wrong, please change the corresponding alarm level








四.紅光中心點

務必保證紅光完全從銅嘴中心出來,否則可能燒毀銅嘴

一般使用硬件調整,即調整尾部電機

Four. Red light center point

Make sure that the red light comes out completely from the center of the copper nozzle, otherwise it may burn the copper nozzle

Generally use hardware adjustment, that is, adjust the tail motor



.切割工件

焦點的要求:負焦相對效果掛渣少

氣體的要求:如果對切割面有要求,建議使用氮氣氣體(大于6公斤),相對切割面發白

                    如果要求切割厚度,使用氧氣或空氣切割,相對切割面發黑

                    不建議使用氬氣切割,可能造成切割效果不良

切割厚度:3毫米以下最好

切割時手速保持均勻

Unlike welding, there is no width for cutting spots

Therefore, the scan width must be set to 0, i.e. the red light is a dot

Scan speed: Ignore this parameter and feel free to do so

Scan width: 0

Peak power: The reference value recommends full power cutting, which is subject to the actual situation

Duty cycle: Reference value 100

Pulse frequency: Refer to 1000

Once the parameters are set, import and go back, and you can see the process on the left side of the home page

Negative focus is recommended (directly affects the cutting effect)

3. Red light center point

Be sure to ensure that the red light comes out completely from the center of the copper nozzle, otherwise the copper nipple may be burned

Hardware adjustment is generally used, that is, the tail motor is adjusted

For adjustment method, please refer to: Adjusting the red light

Fourth, cut the workpiece

The requirements of the focus: the relative effect of the negative focus is less slag

Gas requirements: If there is a requirement for the cutting surface, it is recommended to use nitrogen gas (more than 6 kg), which is whitish relative to the cutting surface

                    If the cutting thickness is required, use oxygen or air to cut, and the relative cutting surface is blackened

                    It is not recommended to use argon for cutting, which may cause poor cutting results

Cutting thickness: 3 mm or less is best

Keep your hand speed even when cutting