熱刺FCA風冷系列激光器與焊接槍的控制接線(中英)

注意:

1.請確保文中的激光器圖示與您使用的激光器為同一型號 本文適用 FCA1000/FCA1500型號

2.如激光器廠家信號更改,則下列接線失效,請按照廠家提供的定義接線

Attention:


1. Please ensure that the laser icon in the article is the same model as the laser you are using. This article applies to FCA1000/FCA1500 model


2. If the laser manufacturer's signal changes, the following wiring fails. Please connect the wiring according to the manufacturer's definition




FCA1000/FCA1500機型圖示

FCA1000/FCA1500 model icon


1.安裝前準備


1.1 熱刺標準風冷整機

1.2 超強焊接槍頭

1.3 超強焊接驅動模塊

(務必為模擬版,請在下單前詢問)

1.4 導熱硅脂

1.5 拆解專用內六角及驅動固定螺絲

1.6 GX20-14母插頭(熱刺附件)

1. Prepare for installation




1.1 Spurs standard air cooling machine


1.2 Super strong welded gun head


1.3 Super welding drive module


(Be sure to be a simulation version, please ask before placing an order)


1.4 Thermal grease


1.5 Remove the special hex socket and drive fixing screws


1.6GX20-14 Female Plug (Tottenham accessories)




2.接線方法


2.1控制部分接線

2.1.1驅動模塊的連線安裝

       通過拆開激光器的后面板,于設備的左下找到驅動安裝的位置,對應接線安裝驅動部分,如視頻

2. Wiring methods




2.1 Connecting Cables to the control part


2.1.1 Cable Installation of the Driver Module


By disassembling the rear panel of the laser, find the driver installation position on the lower left side of the device, corresponding to the wiring and installation of the driver part, such as video





2.2.1 焊接槍的連線安裝

       焊接槍共有3根線,其中兩根黑色的為電機控制線,一根灰色的為扳機按鈕及安全地鎖線, 剪斷后均連接到GX20-14母插頭上,最后插到激光器側蓋板的HEAD I/O上

2.2.1 Connecting the welding gun


The welding gun has a total of 3 wires, of which two are black for the motor control wire, and one is gray for the trigger button and safety lock wire. After cutting, they are connected to the GX20-14 female plug, and finally inserted into the HEAD I/O of the laser side cover plate



   引腳定義如下

Pins are defined as follows

       

2.2氣路部分

超強焊接槍為水冷風冷通用型號,因此會有三根管道,使原水路循環,如下圖綠色管道連接到激光器側蓋板的GAS OUT 氣管上即可,請注意,GAS IN輸入的焊接氣體壓力不可大于1MPa

2.2 Gas path part

The super welding gun is a water-cooled and air-cooled universal model, so there are three pipes to circulate the original water. The green pipe IN the following figure can be connected to the GAS OUT GAS pipe of the laser side cover plate. Please note that the welding gas pressure input by the GAS IN the gas can not be greater than 1MPa





2.3 激光器部分接線


2.3.1 安全地鎖接激光器尾部的CLAMP上,與加工工件相連,提供安全地鎖保護


2.3.2 激光器尾部的CTRL-INTERFACE為12 芯控制信號接口,具體引腳定義如下,提供送絲信號及通訊功能

2.3 Cable Connections to the laser




2.3.1 Securely lock CLAMP on the laser tail and connect to the workpiece to provide safe lock protection




2.3.2 The CTRL-INTERFACE at the tail of the laser is a 12-core control signal interface. The specific pins are defined as follows to provide wire feed signals and communication functions






3.激光器使用方法

參照熱刺說明書

3. Laser use method


Refer to the Spurs instructions